Can i use tung oil over stain

Wait 24 hours and apply a second coat. Two coats are recommended. For additional gloss, repeat after 24 hours. Note: If buffing is difficult, recoat surface immediately and buff.

Coverage: Approximately square feet per quart. Not recommended for floors. Keep away from heat and open flame. We Also Suggest Here are some additional products and tips to explore.

Wood finishing tips, techniques and advice Learn How. Get Inspired. Get inspired by exciting project ideas Get Inspired. View all Preparation products.

View all Stains. Stains have a varnish binder in them to keep the pigment in place, this seals the wood preventing an oil to penetrate into the wood.

Garnet shellac would be my choice. Most any film forming finish will be fine for a wine rack. Wipe-on varnish is almost fool proof. Actually, it is a process. You must understand the properties and tendencies of the finish you are using. You must know the proper steps and techniques, then you must execute them properly.

I will look into garnett shellac, that would be something I have never used before either. I just want to try something new, instead of using the same old thing.

Faust M. Chris, Scott just gave you some good advice. I've enclosed two pictures of a breakfront I built 30 years ago when Formby's Tung Oil finish was all the rage. I used Pure tung oil over oil based stain. I wanted an "in the wood" finish as versus an "On the wood" look. Probably every couple years. If needed you can go over the tung oil with the varnish. My son is building vegetable boxes for a non-profit garden co-op Eagle project.

The wood is poplar. The co-op has requested a food safe pure tung oil. They have also requested us paint a logo on one side of the box in black flat paint. Can we just put the coats of tung oil on that stenciled piece of wood after logo is painted on — simply wiping off tung oil excess over the painted section?

The paint will provide protection on the logo, the tung oil covers the rest? Is that a plan? There is a food safe thinner, citrus solvent, that is food safe. I,m using Tung oil on an indoor floor, on the can it says the oil is toxic and I should use a respirator when applying it. Is this correct? Follow the can instructions for the product you have.

Applied Tung Oil to the top of a Wine Barrel, about 4 coats. Tried knocking the shine down with fine steel wool, but now have very fine scratch marks. Besides applying another coat of Tung Oil, what other options do I have to remove the fine scratches? You could buff the surface with a soft cloth and mineral spirits. Test first before committing to the entire top. Am planning on 3 to 4 coats of tung oil with a light buffing using steel wool between coats.

Wand to wind up with a satin finish. Is this the correct approach? This will work but the Tung oil will remain soft. Another great finish for this is a French Polish.

Great articles about French Polishing. I am finishing a piece of hardwood as a cheeseboard but there are a couple small knots and one larger hole in the wood surface.

I was planning on using a filler for these prior to finishing — any suggestions on filler options that best go with Tung oil? Paste vs. Epoxy for example? Use an epoxy wood filler, little less toxic for a food surface. PC Woody might be a good choice. I am screwed. I installed a wide pine floor in and I used a tung oil and put down about 10 coats. I had some dents and a few chips near the wood stove so In cleaned the surface and applied miniwax tung oil finish on an area about 12 sq feet before i stopped and even thou I was told it was tung oil I realized something was different.

What can I do now to keep the floor looking the same? At this point use acetone or lacquer thinner to quickly remove as much as possible, make sure to use clean white rags and have a bucket of water to dispose the rags in. Hopefully this will remove some of the minwax finish and allow real tung oil to penetrate and hopefully blend. The acetone, finger nail polish remover, is the better bet but lacquer thinner will work in a pinch. This will be really smelly so have windows open, no open flames and make sure to dispose the rags in water.

This morning I used 40 steel wool and I will try the acetone once the fire goes out and my wife leaves to go shopping. Give it a try. Either the acetone or lacquer thinner should dissolve the minwax enough to remove some from the surface and hopefully open us the wood for real tung oil.

You can use the steel wool at the same time to help remove the finish but be careful not to cause deep scratches that will show up later. Your email is never published nor shared. Currently you have JavaScript disabled. In order to post comments, please make sure JavaScript and Cookies are enabled, and reload the page. Click here for instructions on how to enable JavaScript in your browser.

Pages and pages of tips, tricks, and step by step advice. Login Register. Remember me. Forgot your password? Return to login. Applying Tung oil to cleaned and sanded smooth teak patio table top. If you have an article that you would like to publish, then you may submit an article and it will be listed on this site. August 15, at pm. March 16, at am. December 3, at am. February 2, at pm. Wipe off excess oil, keeping only a thin coating on the wood at any time.

Wait for the first layer of oil to dry about 15 to 20 minutes. What is the difference between linseed oil and tung oil? Tung oil requires five or more coats, and you need to sand between each to remove the roughness. Tung oil is more water resistant than linseed oil because it has approximately three crosslinks between molecules instead of the slightly less than two for linseed oil.

What is the difference between tung oil and tung oil finish? Most Tung Oil finishes have petroleum distillates added and generally metallic dryers. Tung Oil will generally build a gloss finish as well as build on top of the wood surface. These types of finish dry over night and require sanding between coats. It however does dry slower than Tung Oil.

How do you buff out tung oil? If its pure tung oil, it can take months to fully cure. If what you have is pure tung oil, thin with 2 to 3 parts mineral spirits before applying. How many coats of tung oil should I use? To get maximum protection, you should apply 3 coats of full-strength tung oil.

You should also have sanded with steel wool the day after applying each coat. How do you remove tung oil from wood?